Lưu ý
Mục đích của file này là để độc giả tiếng Việt có thể đọc và hiểu tài liệu nhân kernel dễ dàng hơn, không phải để tạo ra một nhánh tài liệu riêng. Nếu bạn có bất kỳ nhận xét hoặc cập nhật nào cho file này, vui lòng thử cập nhật file tiếng Anh gốc trước. Nếu bạn thấy có sự khác biệt giữa bản dịch và bản gốc, hoặc có vấn đề về bản dịch, vui lòng gửi góp ý hoặc patch cho người dịch của file này, hoặc nhờ người bảo trì và người review tài liệu tiếng Việt giúp đỡ.
- Bản gốc:
- Người dịch:
Google Translate (machine translation)
- Phiên bản gốc:
8541d8f725c6
Cảnh báo
Tài liệu này được dịch tự động bằng máy và chưa được review bởi người dịch. Nội dung có thể không chính xác hoặc khó hiểu ở một số chỗ. Khi có sự khác biệt với bản gốc, bản gốc luôn là chuẩn. Bản dịch chất lượng cao (được review) được đặt trong thư mục vi_VN/.
IBM’s Journaled File System (JFS) for Linux¶
JFS Homepage: http://jfs.sourceforge.net/
The following mount options are supported:
(*) == default
- iocharset=name
Character set to use for converting from Unicode to ASCII. The default is to do no conversion. Use iocharset=utf8 for UTF-8 translations. This requires CONFIG_NLS_UTF8 to be set in the kernel .config file. iocharset=none specifies the default behavior explicitly.
- resize=value
Resize the volume to <value> blocks. JFS only supports growing a volume, not shrinking it. This option is only valid during a remount, when the volume is mounted read-write. The resize keyword with no value will grow the volume to the full size of the partition.
- nointegrity
Do not write to the journal. The primary use of this option is to allow for higher performance when restoring a volume from backup media. The integrity of the volume is not guaranteed if the system abnormally abends.
- integrity(*)
Commit metadata changes to the journal. Use this option to remount a volume where the nointegrity option was previously specified in order to restore normal behavior.
- errors=continue
Keep going on a filesystem error.
- errors=remount-ro(*)
Remount the filesystem read-only on an error.
- errors=panic
Panic and halt the machine if an error occurs.
- uid=value
Override on-disk uid with specified value
- gid=value
Override on-disk gid with specified value
- umask=value
Override on-disk umask with specified octal value. For directories, the execute bit will be set if the corresponding read bit is set.
- discard=minlen, discard/nodiscard(*)
This enables/disables the use of discard/TRIM commands. The discard/TRIM commands are sent to the underlying block device when blocks are freed. This is useful for SSD devices and sparse/thinly-provisioned LUNs. The FITRIM ioctl command is also available together with the nodiscard option. The value of minlen specifies the minimum blockcount, when a TRIM command to the block device is considered useful. When no value is given to the discard option, it defaults to 64 blocks, which means 256KiB in JFS. The minlen value of discard overrides the minlen value given on an FITRIM ioctl().
The JFS mailing list can be subscribed to by using the link labeled “Mail list Subscribe” at our web page http://jfs.sourceforge.net/