Vietnamese (machine translation)

Lưu ý

Mục đích của file này là để độc giả tiếng Việt có thể đọc và hiểu tài liệu nhân kernel dễ dàng hơn, không phải để tạo ra một nhánh tài liệu riêng. Nếu bạn có bất kỳ nhận xét hoặc cập nhật nào cho file này, vui lòng thử cập nhật file tiếng Anh gốc trước. Nếu bạn thấy có sự khác biệt giữa bản dịch và bản gốc, hoặc có vấn đề về bản dịch, vui lòng gửi góp ý hoặc patch cho người dịch của file này, hoặc nhờ người bảo trì và người review tài liệu tiếng Việt giúp đỡ.

Bản gốc:

octeontx2 devlink support

Người dịch:

Google Translate (machine translation)

Phiên bản gốc:

8541d8f725c6

Cảnh báo

Tài liệu này được dịch tự động bằng máy và chưa được review bởi người dịch. Nội dung có thể không chính xác hoặc khó hiểu ở một số chỗ. Khi có sự khác biệt với bản gốc, bản gốc luôn là chuẩn. Bản dịch chất lượng cao (được review) được đặt trong thư mục vi_VN/.

hỗ trợ liên kết phát triển octeontx2

Tài liệu này mô tả các tính năng của devlink được ZZ0000ZZ triển khai trình điều khiển thiết bị.

Thông số

Trình điều khiển ZZ0000ZZ triển khai các tham số dành riêng cho trình điều khiển sau.

Driver-specific parameters implemented

Name

Type

Mode

Description

mcam_count

u16

runtime

Select number of match CAM entries to be allocated for an interface. The same is used for ntuple filters of the interface. Supported by PF and VF drivers.

Trình điều khiển ZZ0000ZZ triển khai các tham số dành riêng cho trình điều khiển sau.

Driver-specific parameters implemented

Name

Type

Mode

Description

dwrr_mtu

u32

runtime

Use to set the quantum which hardware uses for scheduling among transmit queues. Hardware uses weighted DWRR algorithm to schedule among all transmit queues.

npc_mcam_high_zone_percent

u8

runtime

Use to set the number of high priority zone entries in NPC MCAM that can be allocated by a user, out of the three priority zone categories high, mid and low.

npc_def_rule_cntr

bool

runtime

Use to enable or disable hit counters for the default rules in NPC MCAM. Its not guaranteed that counters gets enabled and mapped to all the default rules, since the counters are scarce and driver follows a best effort approach. The default rule serves as the primary packet steering rule for a specific PF or VF, based on its DMAC address which is installed by AF driver as part of its initialization. Sample command to read hit counters for default rule from debugfs is as follows, cat /sys/kernel/debug/cn10k/npc/mcam_rules

nix_maxlf

u16

runtime

Use to set the maximum number of LFs in NIX hardware block. This would be useful to increase the availability of default resources allocated to enabled LFs like MCAM entries for example.

Trình điều khiển ZZ0000ZZ triển khai các tham số dành riêng cho trình điều khiển sau.

Driver-specific parameters implemented

Name

Type

Mode

Description

unicast_filter_count

u8

runtime

Set the maximum number of unicast filters that can be programmed for the device. This can be used to achieve better device resource utilization, avoiding over consumption of unused MCAM table entries.